New

• Warm Congratulations: Shenzhen Antenk Electronics Co., Ltd. Has passed The Certification of TUV IATF16949:2016 Quality Management System of Automobile Industry 2021-06-18

  Warm Congratulations: Shenzhen Antenk Electronics Co., Ltd. Has passed The Certification of TUV IATF16949:2016 Quality Management System of Automobile Industry

• Introduction of UL Standard Wire And Cable 2021-05-07

  Introduction of UL Standard Wire And Cable Figure 1 UL standard cables are wires and cables produced and inspected according to UL standards of the United States. UL is the abbreviation of underwriter's Laboratory of the United States. It is the most authoritative safety certification organization in the United States. It is also a widely recognized non-profit organization engaged in safety testing and appraisal in the world. It is also the most reliable qualified assessment provider for manufacturers. Specification and unit: The conductor specification of UL is AWG, which means American wire gauge in Chinese. The common UL units are "cmil" (round mils), mil is the unit of length, cmil is the unit of area, the specific use of kcmil and MCM (thousand round mils), 1mcm = 1kcmil = 0.5067 square mm. The values in front of AWG (such as 24awg and 26awg) indicate the number of holes that the wire needs to go through before forming the final diameter. (Figure 1) the larger the value is, the more holes the wire will go through and the smaller the diameter of the wire will be. In other words, the value is small and the wire is thick. AWG is compared with metric system:

• Basic Knowledge of Open/Close Jumper 2021-04-09

  Basic Knowledge of Open/Close Jumper The jumper cap is a small switch for current flow on the circuit board 1. The main board jumper is a manual switch on the main board. The main board circuit can be changed by connecting different jumper pins through the jumper cap. 2. There are two common jumper caps on the motherboard. One is that there are only two pins. 3. The jumper cap is a movable part, the outer layer is insulating plastic, the inner layer is conductive material, which can be inserted on the jumper pin to connect the two jumper pins. 4. When the jumper cap is buckled on the jumper pin, it is in the on state, and there is current passing through. We call it on 5. On the contrary, when the jumper cap is not buckled, it means that it is disconnected, which is called off

• How To Use Machined Pin/Female Header and IC Sockets 2021-04-02

  How To Use Machined Pin/Female Header and IC Sockets The machined pin/female header belongs to one of the categories of pin / female header connector. We should know that the sales volume of machined pin/female header connector in the electronic market is very large and widely used. If you often deal with connectors, then you will not feel strange to the machined pin/female header bus. It is one of the connector categories. It has a large demand in the component market and is widely used. In order to ensure the round hole pin row female connector more reliable in electronic equipment, we must use the correct method, so as to effectively avoid the occurrence of adverse factors. So in the end, how to use the machined pin/female header connector? Here's how to use the machined pin/female header connector. To sum up, there are five ways to use the machined pin/female header

• Shenzhen Antenk Electronics Co., Ltd. 2021.3.30-4.2 ITES Shenzhen Industrial Exhibition 2021-03-30

  Shenzhen Antenk Electronics Co., Ltd. 2021.3.30-4.2 ITES Shenzhen Industrial Exhibition Shenzhen Antenk Electronics Co., Ltd. 2021.3.30-4.2 ITES Shenzhen Industrial Exhibition.Both No.:11-G10,Shenzhen International Convention and Exhibition Center (Bao'an New Museum) . Welcome friends from all walks of life, boss, big shot stop in a hurry, into the booth to drink tea, talk about a few words of life... Antenk Electronic Co., Ltd. strives for improvement on the existing basis, and hopes to improve the development and production capacity through the guidance and requirements of various customers.Professional focus on connector, industrial connector, automotive connector, European socket din416

• 14-16 April 2021 Antenk Electronical China Shanghai Exhibition 2021-01-26

  14-16 April 2021 Antenk Electronical China Shanghai Exhibition 14-16 April 2021 Antenk Electronical China Shanghai Exhibition.Both No:C1-2456.Address:Shanghai New International Eypo Center.The main products of the company are precision board to board, line to board connector, row pin connector, row female connector, European socket connector, simple cow connector, IDC connector, traditional cow horn connector, battery holder connector, battery holder, power signal connector, printed board gold finger bus slot edge card Solt, round hole row pin, round hole row bus, IC base, battery shrapnel, terminal cable / row cable, row cable connector, automobile connector, sample display, catalog, company product album, welcome to visit, consult and obtain. Antenk Electronics Co., Ltd. strives for continuous improvement on the existing basis, and hopes to improve its development and production capacity through the guidance and requirements of customers in all aspects. Shenzhen Antenk Electronics Co., Ltd Sales Hotlin

• 2021 The 11th Shenzhen International Connector, Cable Harness And Processing Equipment Exhibition 2020-12-24

  2021 The 11th Shenzhen International Connector, Cable Harness And Processing Equipment Exhibition Products of Shenzhen Antenk Electronics Co., Ltd. please contact us by telephone for samples or visit booth h385 of hall 1 of the 11th Shenzhen International connector, cable harness and processing equipment exhibition 2021. 2021 the 11th Shenzhen International connector, cable harness and processing equipment exhibition will be held in Shenzhen International Convention and Exhibition Center (Bao'an New Museum) from August 23 to 25, 2021. It will display the application solutions and new technology development direction of various connectors, cable harness and manufacturing equipment in 5g communication, industry, electronic appliances, automobile manufacturing, new energy and other major industries, and vividly interpret the connection Linkage and integration of new manufacturing technology and application of wire harness and cable harness. The last one was opened in Shenzhen Convention and Exhibition Center from September 2 to 4, 2020. With the rapid success of anti epidemic in China, enterprises are also actively exploring the market. Most enterprises seize the opportunity to use this professional exhibition platform to display emerging technology products, strengthen market publicity and cooperation and exchange with purchasers, strive to be the industry vane and seize the market opportunity! It is the confidence of the exhibitors and the market demand of the industry that makes ICH Shenzhen exhibition hot in the past years. ICH Shenzhen 2021 will usher in the 11th session. It is estimated that in 2021,

• Wish You All A Merry Christmas And A Happy New Year in 2021 2020-12-22

  Wish You All A Merry Christmas And A Happy New Year in 2021 ANTENK Electronics Co., Ltd(with the trade mark of "Antenk") was established in 2004. We specialize in producing precise Board to Board,Automotive Connector,Terminal Block Series,Battery Connector,Din41612 Connector,Round hole row needle, round hole row mother, IC socket,battery holders Series,Male Pin Headers Series,Female Pin Headers Series,Modular Jack RJ45 Series,D-Subminiature Connectors Series,Box Header Connector,IDC Socket Connector,SCSI Connectors Series, Wire to Board Connector, Modular Jack, Terminal Block, Wire Harnesses,Cable Assemblies, I/O Connector.

• 2020.11.3-5 electronica South China Shenzhen(Bao An) World Exhibition & Convention Center 2020-10-13

  Electronica South China is the second sub brand exhibition after the brand of electronica China has entered China. Based in Shenzhen, electronica South China in Munich radiates the South China and Southeast Asian markets, builds a high-quality whole industry chain innovation exhibition platform for the electronic industry, gathers well-known enterprises at home and abroad, attracts high-quality buyers and elites in the industry, and creates more business opportunities for the booming electronic industry market in South China. Shenzhen Antaike Electronics Co., Ltd. was invited to participate in the South China Electronic Exhibition in Munich, Shenzhen from November 3 to 5, 2020. The exhibition site is: Hall 12-12b30 of Shenzhen International Convention and Exhibition Center (Bao'an). We sincerely invite all walks of life to visit and guide and negotiate business. We will take the sample display, catalog, product catalog, etc. of BTB, line to board connector, pin connector, female connector, European socket connector, Jane cow connector, IDC connector, traditional horn connector, battery connector, battery holder, terminal line / flat cable, flat cable connector, automobile connector, etc., catalog, company product catalog, welcome to consult and ask for.

• "ATKCONN" trademark registered successfully 2020-09-30

  "ATKCONN" trademark registered successfully Shenzhen Antenk Electronic Co., Ltd., the company's products mainly produce precision plate to board, line to board connector, pin connector, row female connector, European socket connector, jianniu connector, IDC connector, traditional horn connector, battery holder, battery spring, terminal wire

• The difference between SIM card and SD card 2020-09-18

  The difference between SIM card and SD card 1. SIM card is the abbreviation of subscriber identification module, also known as user identification card, smart card. GSM digital mobile phone must be installed with this card before it can be used. The size of Sim can be divided into three types: standard card 25 × 15 × 0.8mm; micro SIM card 12x15 × 0.8mm; nano SIM card 12.3 × 8.8 × 0.7mm; nano SIM card 12.3 × 8.8 × 0.7mm; SIM card size: 25 × 15 × 0.8mm; micro SIM card: 12x15 × 0.8mm; nano Sim card: 12.3 × 8.8 × 0.7mm; In general, the IC chip of SIM card has 128KB storage capacity, which can store the following information: 1000 sets of telephone numbers and their corresponding names and characters, 40 groups of short messages, more than 5 groups of newly dialed numbers, and 4-digit SIM card password (PIN). There are more than 16K, 32K, 64K, 128K, 512k and 1m SIM cards on the market, as well as professional SIM cards that can provide multimedia services and non-contact services. The capacity can reach M-level. 2. The SD card was jointly launched by Panasonic, Toshiba and SanDisk, and was released in August 1999. The data transmission and physical specification of SD card is developed from MMC. The size of SD card is similar to that of MMC card. The size is 32 x 24 x 2.1 mm. The length and width of the MMC card are the same, but 0.7mm thicker than the MMC card to accommodate a larger storage unit. SD and MMC cards are compatible upward. MMC cards can be accessed by new SD devices. Compatibility depends on application software, bu

• Antenk: Winning The 《BOSSGOO AUDITED SUPPLIER》 2020-09-08

  Antenk: Winning The 《BOSSGOO AUDITED SUPPLIER》 Recently, Shenzhen Antenk Electronics Co., Ltd. (hereinafter referred to as "Antenk"), which focuses on the manufacture of electronic connectors and wiring harness, has won the honorary title of "BOSSGOO AUDITED SUPPLIER". For Antenk, this is both recognition and encouragement. "A group of people, one heart, together, will win." The short and powerful 12 words represent Antenk's corporate goal and vision: connect the world, connect the future, and become a well-known connector brand. Antenk was founded in 2004 and has developed for 16 years. It has been awarded the honorary titles of "national high tech enterprise", "Shenzhen patent training enterprise" and "contract abiding and trustworthy enterprise". Its independent brand "antenk" has been awarded "Guangdong famous trademark". "International cable and connection" reporter interviewed Yang Guoli, general manager of Antenk, to understand its current enterprise situation and its future market layout. Shenzhen Antenk Electronic Co., Ltd. The company's products mainly produce precision plate to board, line to board connector, row pin connector, busbar connector, European socket connector, jianniu connector, IDC connector, traditional horn connector, battery holder connector, battery spring piece, terminal line / flat wire, flat wire connector, automobile connector, et

• Application of Anti Stay In Connector 2020-09-07

  Defraive (foolish proofing) is one of the best way to prevent the problem, and to avoid the demand of the customer, and to avoid the demand of the demand, the demand of the demand, and the demand of the demand. On the other hand, it is possible to prevent the loss of the operation of the person who is involved in the loss of the operation desk or the human body. 1 For example, the usual desk desk SIM cards, there are some special advantages, and it is not possible to prevent it from being damaged, and it is not possible to put it out, and the prevention of the new hand operation sim. 2 sources In the management of the business of the Japanese original Japanese chess and the chess game, the management of the enterprise for the empress is the basic concept of the Dakota, a new way of thinking in Japan, Shigeo Shingo, Shigeo Shingo. Devastation day is "pokake", "Poka" original, "idiot", immediate fool intention, "yoke" is a defensive intention, and it is "POW yoke", and "fool proofing". It is an immense or foolish way. Defensive 1. Have a structure that can't be wrong even if someone is negligent - no attention required. 2. Have a structure that can be done by laymen without experience and intuition 3. Have a structure that doesn't go wrong no matter who or when you work - no expertise or high level o

• Press Conference on The Completion and Opening of Beidou-3 Global Navigation Satellite System 2020-09-07

  Press Conference on The Completion and Opening of Beidou-3 Global Navigation Satellite System On the morning of August 3, 2020, the press conference on the completion and opening of beidou-3 global navigation satellite system was held in the Information Office of the State Council. Ran Chengqi, director of China satellite navigation system management office and spokesman of Beidou satellite navigation system, Xie Jun, deputy chief designer of Beidou system engineering and chief designer of beidou-3 satellite system, Lin Baojun, chief designer of beidou-3 satellite system, and Chen Jinping, chief designer of beidou-3 project operation and control system, attended the press conference to introduce beidou-3 global satellite The satellite navigation system has been completed and put into operation. Ladies and gentlemen, dear media friends Good morning, everyone. It's a great pleasure to attend today's press conference with my three colleagues. In July 31st, general secretary Xi Jinping announced to the world that the Beidou three global satellite navigation system was officially opened, marking the successful completion of the "three step" development strategy of Beidou, and the Beidou stride into a new era of global service. Next, I will introduce the situation from four aspects. 1. The project construction was completed half a year ahead of schedule, showing the speed of China Overcome the difficulties and finish the job perfectly. Beidou-3 started construction in November 2009. Over the past 10 years, the project construction has gone through five stag

• ICH Shenzhen 2020 Shenzhen Exhibition Review 2020-09-07

  ICH Shenzhen 2020 Shenzhen Exhibition Review Grand ceremony of the industry, focusing on application technology innovation and upgrading The 10th Shenzhen International connector, cable harness and processing equipment exhibition was held in Shenzhen Convention and Exhibition Center from September 2 to 4. With the topic of "intelligent industry, connector future", the 10th Shenzhen International connector, cable harness and processing equipment exhibition was held in Shenzhen Convention and Exhibition Center from September 2 to 4. It solved the problems of manual operation of products from precision manufacturing technology, product design, process technology and quality control technology, and enhanced the core competitiveness. ICH Shenzhen 2020 will directly focus on technological innovation, promote product upgrading, and show cutting-edge new technologies, new processes, new equipment, new materials and new products. The exhibition covers all kinds of electronic / industrial / automobile connectors, connector terminal welding and assembly equipment, automatic processing equipment for various cable harness and wire ends, connector / cable harness detection instruments, automatic production line solutions, various finished cable bundles and various data wires, wiring equipment, cable manufacturing and materials. It aims to create an efficient technology and business exchange platform of "brand display, economic and trade negotiation and technical exchange" for application manufacturers from different industries all over the world. The popularity of ICH Shenzhen exhibition did not decrease in previous years. W

• Simple Classification and Identification of USB Interface Types 2020-08-29

  Simple Classification and Identification of USB Interface Types 1. First of all, with more and more smart devices, there will be a variety of USB interfaces. For many people, there are only three interface types: USB interface, Android interface and apple interface. As for type-C, it will be called another Android interface. Antaike Xiaobian, take you to sort out these USB interfaces. 2. Common interfaces type A, micro B, type C; a. Type A: mainly used on computers b. Micro B: it is commonly used in Android phones (common in low and medium end, and more and more mobile phones adopt type C), as well as various charging devices c. Type C: at present, it is commonly used in medium and high-end mobile phones, such as various flagship phones of Android. More and more other devices also have this interface, such as notebook, mobile hard disk, motherboard 3. Many external USB devices such as printer and monitor USB hub adopt type B interface. Generally speaking, the USB interface on PC is standard type A, while the external devices mostly use type B. 4. Compared with 2.0, USB 3.0 not only has advantages in speed, but also has advantages in charging current. At the beginning of 2.0 release, 500mA current can meet the power supply of all USB devices, but with the development of science and technology, today's peripherals usually need more current.

• Models and Sizes of Common Mn Zn Batteries and Li MnO 2 Button Batteries 2020-08-28

  Models and Sizes of Common Mn Zn Batteries and Li MnO 2 Button Batteries Battery model editing Generally divided into: 1.2.3.5.7, of which No. 5 and No. 7 are particularly commonly used. The so-called AA battery is No. 5 battery, and AAA battery is No. 7 battery. D-type battery (large battery / lr20 / AM1) has a diameter of 34.2 and a height of 61.5mm Type C battery (No.2 battery / LR14 / AM2) has a diameter of ф 26.2 and a height of 50.0 mm AA type battery (No.5 battery / LR6 / AM3) has a diameter of ф 14.5 and a height of 50.5mm The diameter of AAA type battery (No.7 battery / LR03 / AM4) is ф 10.5 and the height is 44.5mm AA / 2 battery (No.8 battery LR1 / Am5) has a diameter of Φ 11.0 and a height of 30.0 mm AAAA battery (No.9 battery / lr61 / am6) with diameter of ф 8.0 and height of 39.5mm AAAA / 2 battery (small No.9 battery / lr61 / am6) with diameter of ф 8.0 and height of 28.0 mm Other models

• Basic Structure Knowledge of FPC Connector and FFC / FPC Flat Cable Connector 2020-08-20

  1. FPC connector is mainly used in LCD, scanner and other electronic equipment, widely used in computer motherboard, LCD display, telecommunication card, memory, mobile hard disk, including mobile devices. In recent years, mobile devices (such as mobile phones, players, recorders, displays, tablets and laptops) are more and more popular in our life. FPC connector is particularly important as a transmission bridge. The specific application products are: automotive electronic connector, vehicle GPS navigation, medical equipment, speaker, digital machine, camera, car audio, TV, typewriter, calculator , cash register, telephone, CD-ROM, VCD, DVD, copier, printer, wireless instrument, call equipment and aerospace products. Main features: 1) miniaturization, compact and high density integration; 2) space saving; 3) simplified wiring procedure; 4) simple connection; 4) labor cost saving; 5) excellent flexibility, flexible application and foldable. The conventional spacing of products: ① the distance between the wires: 0.3 mm, 0.5 mm, 0.8 mm, 1.0 mm, 1.25 mm, 2.0 mm, 2.0 mm, 2.54 mm, 2.0 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.0 mm, 2.5 mm, 2.5 mm, 2.0 mm, 2.54 mm, 2 mm, 1.0 mm, 1.3 mm, 1. 2. FPC connector can be thin and miniaturized in order to reduce the occupied area The first part of the rubber core, the main role is to protect the terminal, insulation, connection of the correct, to provide the strength of the mechanism

• Main Production Process of Connector 2020-07-25

  1. Stamping: the manufacturing process of the connector generally starts from stamping, and passes through the large-scale high-speed stamping machine. The connector (pin and other metal parts) is punched by thin metal belt. One end of the large coil metal belt is sent to the front end of the stamping machine, and the other end is wrapped into the coiling wheel through the hydraulic workbench of the stamping machine. The metal belt is pulled out by the coiling wheel and the products are rolled and punched. 2. Electroplating: after stamping, it should be sent to electroplating section. At this stage, the electronic contact surface of the connector will be coated with various metal coatings. Similar to the stamping stage of a class of problems, such as distortion, fragmentation or deformation, will also appear in the process of stamping into the electroplating equipment, quality defects are very simple to detect. 3. Injection molding: commonly used in PBT, LCP, PA66. PA6T, PA9T injection molding rubber shell, rubber core. For Example Board to Board,

• Review of Antenk electronic Electronica China Shanghai Exhibition held on July 3-5, 2020 2020-07-06

  ANTENK Electronics Co., Ltd(with the trade mark of "Antenk") was established in 2004. We specialize in producing precise Board to Board,Automotive Connector,Terminal Block Series,Battery Connector,Din41612 Connector,battery holders Series,Male Pin Headers Series,Female Pin Headers Series,Modular Jack RJ45 Series,D-Subminiature Connectors Series,Box Header Connector,IDC Socket Connector,SCSI Connectors Series, Wire to Board Connector, Modular Jack, Terminal Block, WireHarnesses,Cable Assemblies, I/O Connector.Through 15 years of development, we have grown into a leading manufacturer in Asia. We have passed ISO9001:2008 and ISO1400 Certification as well. Mostly of our products have been approved by UL, SGS and RoHS. Since its foundation, ANTENK sticks to the principle of specialization and tries its best to supply customers with products of high quality at competitive prices, by the precision high-speed punch molding, precise plastic injection molding and automatic assembly with the support of a skilled R&D and management team. The factory, with 3000M² floor plant, has about 100 employees and owns 15 sets precision molding devices, 4 sets Japan & Taiwan precision high-speed punch machines, more than 300 sets Various types of plastic molds and more than 100 sets hardware terminal molds, 10 sets laboratory testing equipments and over 50 sets machines for automatic assembly that can provide customer with over 10 types and 10,000 different specification connectors parts, company have import-export handles rights. And up to 70% products are exported to Euro-American countries. Mainly customers: Foxconn, Flextronics, Molex, Amphenol, FCI, Siemens etc. famous companies.

• 2020 The 10th Shenzhen ICH international Connector Cable Harness and Equipment Exhibition 2020-06-17

  2020 The 10th Shenzhen ICH International Connector Cable Harness And Equipment Exhibition Exhibition Time: September 2-04, 2020 Exhibition Venue: Shenzhen Convention And Exhibition Center Shenzhen Antenk Electronic Co., Ltd Booth No.: 2a596 ANTENK Electronics Co., Ltd(with the trade mark of "Antenk") was established in 2004. We specialize in producing precise Board to Board,Automotive Connector,Terminal Block Series,Battery Connector,Din41612 Connector,battery holders Series,Male Pin Headers Series,Female Pin Headers Series,Modular Jack RJ45 Series,D-Subminiature Connectors Series,Box Header Connector,IDC Socket Connector,SCSI Connectors Series, Wire to Board Connector, Modular Jack, Terminal Block, Wire Harnesses,Cable Assemblies, I/O Connector.Through 15 years of development, we have grown into a leading manufacturer in Asia. We have passed ISO9001:2008 and ISO1400 Certification as well. Mostly of our products have been approved by UL, SGS and RoHS. Since its foundation, ANTENK sticks to the principle of specialization and tries its best to supply customers with products of high quality at competitive prices, by the precision high-speed punch molding, precise plastic injection molding and automatic assembly with the support of a ski

• July 3-5th,2020 Shanghai New International Expo Center Electronica China Exhibition 2020-05-22

  ANTENK Electronics Co., Ltd(with the trade mark of "Antenk") was established in 2004. We specialize in producing precise Board to Board,Automotive Connector,Terminal Block Series,Battery Connector,Din41612 Connector,battery holders Series,Male Pin Headers Series,Female Pin Headers Series,Modular Jack RJ45 Series,D-Subminiature Connectors Series,Box Header Connector,IDC Socket Connector,SCSI Connectors Series, Wire to Board Connector, Modular Jack, Terminal Block, Wire Harnesses,Cable Assemblies, I/O Connector. Through 15 years of development, we have grown into a leading manufacturer in Asia. We have passed ISO9001:2008 and ISO1400 Certification as well. Mostly of our products have been approved by UL, SGS and RoHS. Since its foundation, ANTENK sticks to the principle of specialization and tries its best to supply customers with products of high quality at competitive prices, by the precision high-speed punch molding, precise plastic injection molding and automatic assembly with the support of a skilled R&D and management team. The factory, with 3000M² floor plant, has about 100 employees and owns 15 sets precision molding devices, 4 sets Japan & Taiwan precision high-speed punch machines, more than 300 sets Various types of plastic molds and more than 100 sets hardware terminal molds, 10 sets laboratory testing equipments and over 50 sets machines for automatic assembly that can provide customer with over 10 types and 10,000 different specification connectors parts, company have import-export handles rights. And up to 70% products are exported to Euro-American countries. Mainly

• The Basic Knowledge of The Classification and Selection of Terminal Specifications and Models 2020-05-22

  ANTENK Electronics Co., Ltd(with the trade mark of "Antenk") was established in 2004. We specialize in producing precise Board to Board,Automotive Connector,Terminal Block Series,Battery Connector,Din41612 Connector,battery holders Series,Male Pin Headers Series,Female Pin Headers Series,Modular Jack RJ45 Series,D-Subminiature Connectors Series,Box Header Connector,IDC Socket Connector,SCSI Connectors Series, Wire to Board Connector, Modular Jack, Terminal Block, Wire Harnesses,Cable Assemblies, I/O Connector. The basic knowledge of the classification and selection of terminal specifications and models The classification of terminal blocks can be divided in several ways. At present, there are three common methods. According to the terminal raw materials, such as copper terminals, according to the terminal functions, such as printed circuit board terminals, the last one is the more familiar classification by the market, according to the connection form of terminals, mainly including the following categories:

• Happy new year 2020 2019-12-11

  Wishing you peace, joy and happiness through Christmas and the coming 2020 year!